Installing a water filter in your bathroom is a great way to reduce the number of contaminants and impurities in your water. Not only will it improve the quality of your water, but it can also extend the life of your plumbing fixtures. This guide will walk you through the process of choosing and installing a water filter in your bathroom.
Pick The Appliance
The first step, of course, would be that you get the right appliance for this to work properly. Lots of homeowners are on the lookout for the AquaBliss SF220 Shower Filter in order to make sure their skin is protected at all times. Finding the right gear for this job takes time and patience.
Putting the right system in place will ensure that you get the most out of your bathroom water filtration and purification. When picking an appliance for this purpose, it’s important to consider what type of system is best suited for your home. It’s also important to think about how many people will be using the water, and what kind of contaminants you need the appliance to remove
Gear Up
Once you have the right system figured out, it’s time to gather the tools you’ll use for the project. Here are the pieces you will need:
- An aerator or inline water purifier
- A sink faucet adapter
- A shutoff valve
- A filter housing wrench
- A flexible water supply line
- Replacement filters
- A drain line
Make sure to buy the right tools and learn how to use them. It’s important to have the right tools for the job, and they should be used correctly in order to achieve optimal results. If you’re feeling a bit unsure about any of the steps, it may be worth hiring a professional plumber to help ensure that your system is safely installed and operating properly.
Turn The Water Supply Off
Before you start working on the project, it’s essential that your water supply is turned off. This will help ensure that you don’t get splashed with contaminated water while you’re filtering and purifying it. You may need to turn off the main valve or just the one in your bathroom, you should consult a professional if you’re not sure how to do this safely.
For example, if you don’t know how to turn the water supply off for your bathroom sink, you may need to contact a plumber. In most cases, turning off the main valve is enough to shut down all of the water running into your house.
Once the water supply has been turned off, you can start working on replacing old plumbing parts and finally installing a filter and/or purification system. Not only will turning off the water supply protect your safety, but it also gives you time to research some of the different options available for improving your bathroom’s water quality.
Cut The Water Pipes
You’ll need to carefully cut the water pipes entering your bathroom in order to filter and purify the water before you can use it. It’s important to ensure that this cutting is done correctly, or else it could cause a leak that would need repairing.
First, turn off the main water shutoff valve before cutting the pipes connected to your bathroom fixtures. You’ll then want to measure and mark where you’ll cut them with a permanent marker. This will help ensure that your cuts are even and smooth.
Once you’ve marked where you’re cutting, use a pipe cutting tool such as a hacksaw or tubing cutter to create your cuts. If possible, try cutting in one continuous motion. If not, make sure that each individual cut is even.
Install A Filter Cartridge
Put the filter cartridge between the pipes you plan to use for filtering. Tighten the fitting by hand, then use a wrench on the plastic fittings until it’s securely fastened. Next, fill up the cartridge with water so that it’s completely submerged and ready to filter. Make sure all of the seals are tight and not leaking around the sides of your pipes and fittings.
Now you can turn on your bathroom faucet to allow water into the filter cartridge, which is now installed between two pipes in your bathroom plumbing system. You should also check if there is any air coming out from the backflow valve or other places, as this indicates a leak in your system. If there is air coming out, turn off your faucet and make sure your seals and fittings are properly connected.
Once the filter cartridge is filled with water, you should check its performance. This can be done by installing an inline pressure gauge to measure the pressure drop in the system, which indicates how much of the contaminants have been removed from the water.
Hook Up The Device
Once installed, you can hook up your device to start using it. Connect one end of a hose to the hook up at the back of your device and attach the other end to the hot water supply in your bathroom. When hooking up, ensure that you have firm connections with no gaps or cracks.
When connected, turn on the hot tap in your bathroom and check that there is consistent water flow into your device. If not, try adjusting the hook-up connectors until you get a steady stream of water running through your filter system. You are now ready to enjoy clean, filtered bathroom water!
Protect The System
Having clean water in your home is essential, so protecting the system is paramount to keeping it clean and safe. Follow the manufacturer’s maintenance instructions for your system. This may include replacing the filter cartridge on a regular basis, cleaning the system, and checking for leaks.
Additionally, keep the system clean from dirt or debris accumulating on the system, and clean it off to prevent contamination. Make sure to keep it away from contamination sources such as sewage pipes, chemicals, or other hazardous materials. Finally, make sure to regularly test the water quality to make sure that the system is working properly. There are many different water testing kits available that can help you identify any potential problems with your water.
Clean water is a luxury you must give yourself to make sure you stay healthy at all times, so stay by picking the appliance and gathering the tools you’ll need. Turn the water supply off and cut the pipes where you will install the cartridge. Once done, it’s time to hook up the device and connect the system. The final step is to keep maintaining and protecting it at all times!
